Yeast hydrolysate SUS304 SU316 LPG Series High speed Centrifugal
Spray Drying Equipment for foodstuff
beer yeast spray dryer, the spray drying is the widely used
technology in the liquid shaping technology of dryig industry. It
is most suitable for producing powder, partical or block solid
products from material of solution, emulsion, soliquoid and
pumpable paste states.
The clean air is heated and entered into drying tower,the raw
material inside the tower is atomized into fine mist through
muzzles of two or three flows. The raw materials carry out heat
exchange with the hot air rapidly to evaporate the moisture in the
raw materials. The moisture or solvent is discharged accompany with
hot air, then the power product is produced.
after been filtered and heated the air enters into the air
distribustor on the top of the dryer, the hot air enters into the
drying chamber in the spiral form and uniformly. passing through
the high-speed centrifugal atomizer on the top of the tower, the
material liquid will rotate and be sprayed in to extremely fine
liquid beads. through the very short time of contacting the hot
air, the materials can be dried in to the final product. the fianl
product will be discharged continuously from the bottom of the
drying tower and from the cyclone. the waste gas will be exhausted
by exhaust fan.
The drying speed is high when the material liquid is atomized, the
surface area of the material will increase greatly. In the hot-air
flow, 95%-98% of water can be evaporated at a moment. The time of
completing the drying is only several seconds. This is especially
suitable for drying the heat sensitive materials. Its final
products own the good uniformity, flow ability & solubility.
And the final products are high in purity and good in quality. The
production procedures are simple and the operation and control are
easy. The liquid with moisture contents of 40-60% (for special
materials, the contents might be up to 90%.)can be dried into the
powder or particle products once a time. After the drying process,
there is no need for smashing and sorting, so as to reduce the
operation procedures in the production and to enhance the product
purity. The product particle diameters, looseness and water
contents can be adjusted through changing the operation condition
within a certain range.
ed centrifugal sprayer on the top of the tower, the material liquid
will rotate and be sprayed into the extremely fine mist liquid
beads. Through very short time of contacting the heat air, the
materials can be dried into the final products. The final products
will be discharged continuously from the bottom of the drying tower
and from the cyclones. The waste gas will be discharged from
- YIBU conventional Spray Dryer turns liquid into powder in a highly
efficient manner. It is used within fields as diverse as the dairy,
food and chemicals industries where it has won renown for its
performance. With more than 2,500 spray dryers installed worldwide,
YIBU Dryer combines experience and cutting-edge technology into
added-value solutions for its customers.
- Designed for the specific product to be dried in compliance with a
given industry’s standards and requirements, the conventional Spray
Dryer produces a fine powder with particle sizes between 20-300 my.
It is primarily applied in the chemical industry, but it has also
proved valuable in the production of food and dairy products.
- Atomization of the concentrate takes place via either a Rotary
Atomizer or high-pressure nozzles. The drying air enters through
the air disperser at a high velocity, ensuring optimal mixing with
the atomized concentrate. Evaporation is instantaneous, taking
place as the droplets pass through the drying chamber.
- Complete control of moisture content, particle structure, particle
size distribution, solubility, and wettability, and retention of
natural aromas and flavours.
- Unbeatable performance/cost ratio Energy efficient components,
continuous and rapid drying, ease of operation and process
automation provide complete control over yield and costs.
|Model||High speed centrifugal spray Dryer MODEL LPG-|
|Inlet air temperature||≤ 350°C|
|Outlet air temperature||80-90°C|
|Evaporate capacity (kg/h)||5||25||50||100||150||200-5000|
|Atomizer type||compressed air drive||mechanical drive|
|Diameter of atomizer disc (mm)||50||120||120||120||150||180-500|
|Electric-heating power (kw)||9||-||-||-||-||-|
|Dry powder yield (%)||≥ 95||≥ 95||≥ 95||≥ 95||≥ 95||≥ 95|